Types of Fits: How to Choose a Fit for Engineering Application

November 27, 2024 0 By

The true art of engineering is seen in complex mechanical assemblies. Take a look inside a wristwatch; the perfect harmony in which all the tiny components work together is nothing less than mesmerizing. This is a prime example of engineering fits, which are the topic of this discussion.

In this article, we will talk about the different types of fits, their standards, applications, and some common techniques to create them. Let’s get started!

Contents
hide

I
What is an Engineering Fit?

II
Basis of Fits: Hole and Shaft System

III
Types of Fits

IV
Engineering Fits: The Big Picture

V
How to Achieve Dimensional Tolerances for Fits?

VI
Conclusion

VII
FAQs

What is an Engineering Fit?

Engineering fits are a kind of mechanical assembly where two mating parts are joined together, either permanently or temporarily. The word ‘fit’ characterizes the amount of mechanical clearance, or the extent of physical contact, between the mating components.

If the parts are fit together tightly and the joint can carry loads, it is an interference fit. On the other hand, a transition fit characterizes a joint that carries sufficient force to maintain contact but cannot withstand high loads. The third category, clearance fit, has a small gap between the mating components, allowing free rotation or sliding between them.

Basis of Fits: Hole and Shaft System

The hole and shaft basis system is a popular standard for engineering fits. It has two variants: hole-basis or shaft-basis systems. For both, the base component has fixed dimensions while the other component is sized to achieve the fit. For example, in the shaft-basis system, the shaft diameter is fixed and the hole diameter is adjusted.

Of these two, the hole-basis system is by far the most popular as it is more convenient to control the diameter of shafts compared to holes.

The shaft-basis system is not completely disregarded though. When sizing the shaft is infeasible, for instance with a high-speed rotating shaft after mass balancing, the hole size is altered to achieve the fit.

Types of Fits

As we briefly mentioned before, there are three main categories of engineering fits. Each one has a different mechanical contact and a different job to perform. In this section, we dive deep into these types of fits and their sub-categories.

1. Interference Fit

The interference fit is a type of engineering fit where high frictional force tightly holds the mating surfaces together. Consequently, the interference fit is also known as a friction fit.

The tightness of interference fits comes from its negative clearance. This means that the mating surfaces press into each other. In other words, the mating surfaces deform inwards under contact pressure. For instance, in a hole and shaft system, the hole is actually smaller than the shaft in an interference fit. The shaft is forcefully press-fit (another name for interference fit) into the hole via a hydraulic press or hammers.

Additionally, another common method to create interference fits is by shrink-fitting. In this technique, one of the parts is either cooled or heated so that it contracts or expands (respectively) enough for the negative clearance to momentarily change to positive clearance. After locating the parts against each other, the temperatures normalize. The resulting thermal shrinkage/expansion creates a tight interference fit.

Generally, the clearance in an interference fit is -0.001mm to -0.042mm. Now, let’s see the sub-categories of interference fit:

Press Fit: A lighter variant of press fitting with minimal negative clearance for medium-strength joints.

Driving Fit: Medium interference joint that can carry loads and requires cold/hot pressing and force to assemble.

Forced Fit: Forced fits are the strongest type of engineering fit. They require cold/hot pressing and are almost always permanent. Their assembly warrants careful tolerancing and placement to avoid the breakage of parts.

2. Clearance Fit

A clearance fit has a positive allowance. This means that there is a slight gap between the mating surfaces. As a result, the parts also have some play, but it is negligible and often not observable to the naked eye.

Due to this play, parts in a clearance fit have a certain degree of freedom (of movement). For example, the pin and frame in pivot joints have a clearance fit, allowing both components to move independently of each other but also stay locked in place at the same time.

The common range of clearance in these engineering fits is +0.025mm to +0.089mm. A summary of the clearance fit types is as below:

Loose Running: The clearance is set at the higher end of the range given above. Parts in a loose running clearance fit are free to rotate/slide and have an observable play.

Free Running: Similar to a loose running joint. Parts can move at high speeds and the joint can accommodate thermal expansion. However, the location accuracy is low due to considerable play.

Close Running: Close running fits have a slightly better positioning accuracy and allow parts to move even at high temperatures and speeds.

Sliding: Sliding joints are high-accuracy engineering fits. Clearance is kept to a minimum to restrict all degrees of freedom except in the sliding direction.

Location: Location fits are very high-precision fits to locate the mating parts accurately. The clearance is very low and requires lubrication to allow smooth motion.

3. Transition Fit

Transition fit is a middle ground between the other two engineering fits. Depending on the application, the mating parts can have either a small interference or clearance.

If there is a negative interference, like an interference fit, the pressure and load-carrying capacity is not that high. If there is a clearance, as with a clearance fit, there is not as much play.

Typically, a transition fit is useful for precision-locating parts in assembly operations. It restricts their relative movements while also preventing extreme mechanical stresses.

The mechanical interference/clearance in transition fit ranges between +0.023mm to -0.018mm. Furthermore, transition fit has two common types:

Similar Fit: A very light engineering fit with near-zero clearance/interference. Generally, a human-applied force with a mallet is sufficient to achieve the fit.

Fixed Fit: Slightly tighter than a similar fit that requires a press to achieve.

Engineering Fits: The Big Picture

The information in the previous section can be too much to absorb in one go. To understand it better, let us zoom out a bit and try to get a bird’s eye view of engineering fits. A great way to do this is to discuss common engineering standards for types of fits.

The two most popular standards regarding engineering fits are ISO 286 and ANSI B4.1. Both standards provide comprehensive information on tolerance ranges for different fit types. One can find reference tables from these standards in every fabrication shop, signifying their importance in the industry.

Since the ISO standard is the more well-known of the two, the following chart focuses on it.

Type of Fit Hole Basis Shaft Basis Fit Type Applications Clearance Fit H11/c11 C11/h11 Loose Running Fit Pivots, parts with corrosion and dust, parts exposed to thermal changes H9/d9 D9/h9 Free Running Fit Cylinder-piston assemblies, slow-rotating parts H8/f7 F8/h7 Close Running Fit Machine tool spindles, shaft bearings, sliding joints H7/g6 G7/h6 Sliding Fit Sliding gears, clutch disks, hydraulic pistons H7/h6 H7/h6 Locational Clearance Fit Machine tool guides, roller guide rails Transition Fit H7/k6 K7/h6 Locational Transition Fit Wheels, brake disks, gears/pulleys on shafts H7/n6 N7/h6 Locational Transition Fit Motor armature windings, gears Interference Fit H7/p6 P7/h6 Locational Interference Fit Hubs, clutches, bushings for bearings H7/s6 S7/h6 Medium Drive Fit Permanent gear/pulley assemblies, bearing mounting H7/u6 U7/h6 Force Fit Flange mounting, gears, shafts

How to Achieve Dimensional Tolerances for Fits?

It is clear from the above discussion that dimensional tolerance is a critical factor for accurate engineering fits. However, manufacturing the mating parts within the required dimensional tolerances is a skillful task.

Generally, the tolerance limits are included in engineering drawings via appropriate GD&T symbols. GD&T sets acceptable limits on the amount and nature of geometric deviations from the true geometry. Thus, the fabricator must manufacture the parts within these set limits.

There are numerous techniques manufacturers may utilize to achieve this. These include:

CNC Precision Machining: CNC machines have remarkable accuracies up to +/- 0.001mm. Using the correct tooling and fixturing, machinists can produce accurate parts for engineering fits.

Grinding: Grinding is the go-to method for ultra-precise manufacturing owing to its impressive manufacturing accuracy of +/- 0.25 microns. For critical applications like a forced interference fit, tolerances of this order are common.

Reaming: It is a specialized application for hole-making. Since holes are a very common mating component in engineering fits, reaming is worth a mention in this list. Since it is a precise method that removes a minuscule amount of material, it is useful in bringing holes within the tight dimensional tolerances required for mechanical fits.

Conclusion

Engineering fits are indispensable for the manufacturing industry. We would not have assembled products without them! The three fit types: interference fit, transition fit, and clearance fit, all play essential roles in various products like shafts (gears, pulleys, and bearings), machine tool slides, clutches, etc. Therefore, it is great to be knowledgeable about this topic as a technical professional.

WayKen is an ISO-certified rapid prototyping company. Our diverse range of services includes precision machining, 3D printing, and rapid tooling, where we take special care to achieve the right types of fits for your specific applications. Feel free to contact us for your projects.

FAQs

What are the fits and tolerances?

Fits, or mechanical/engineering fits, are a type of mechanical joint where two parts are assembled together with some clearance between their mating surfaces. The clearance can be positive or negative based on the type of mechanical fit. Tolerances are the dimensional limits within which these parts must be produced in order to achieve the correct type of fit.

How to choose a fit for my application?

The choice of engineering fit depends upon several factors. The amount of movement or load-carrying capacity of the joint is the first consideration. Other important factors include the quality and strength of components being assembled, part geometry, manufacturing capability, and fabrication costs.

How to calculate engineering fit tolerance?

Engineering fit tolerances can be selected using guidelines from well-known engineering standards like ISO or ASME. One can find detailed information on engineering dimensions and tolerances for each type of fit and hole/shaft size.

Keyword: CNC machining